Loosen the belt tensioner bolt and push the tensioner away from the belt. The average price of a 1997 Ford Contour timing belt replacement can vary depending on location.
Only one of the cam pulleys has a mark on it as well.
1997 ford contour timing belt marks. If you check the maintenance schedule for your Ford Contour you will not see anything about the timing belt until 120000 miles. Get the best deals for an aftermarket 1997 Ford Contour Timing Belt replacement. Chiesto da Jeremywa78 middot 1 RISPOSTA 6 IMMAGINI 1999 CONTOUR FORD 1999 Ford Contour Timing Marks Come faccio a impostare i segni di fasatura per la mia Ford Contour 20l 4 Cyclinder del 1999.
Tighten the retaining bolt to 81-89 ft. 1997 Ford Contour – Need a diagram of timing belt alignment – 1997 Ford Contour- question about Cars Trucks. 1997 Ford Contour Timing Belt Removal And Installation.
Loosen the tensioner bolt so the spring can pull it tight against the belt. Reinstall the lower timing belt cover and tighten the retaining bolts to 53-71 inch lbs. Identifying Timing Belt Tensioner Courtesy of FORD MOTOR CO.
Ensure camshaft alignment tool is still installed. Apply silicone sealer to the key-way of the crankshaft pulley and install. Position the new timing belt on the pulleys and verify that all the timing marks are properly aligned.
Hello i want to set the timing on a 1997 ford contour with 4 cyl people say by putting a bar to hold the cam in place is this right or is the only way to do this is by the book and take the valve cover off and put the bar in place on the back side of the cam and take off the covers on the front side of the motor and remove the timing belt and adjust the timing and such as the book says. Its a 20 z-tech than rolled over rough but seemed. Typical trade practice suggests that as a precaution the timing belt should be replaced every 60000 miles as in all other similar engines as timing belts tend to stretch.
However many other manufacturers recommend replacing the timing belt at 60000 miles. The OEM Ford has not recommended a timing-belt replacement interval for the 1995 through 1997 Ford Contour 20 engine. Install timing belt on crankshaft sprocket.
Browse The solution for your car repair. Fast shipping with low price guarantee. What are timing marks for 1997 ford conyour 20 engine dual overhead cams replacing timing belt old one broke – Ford Contour question Search Fixya Press enter to search.
Average failure mileage is 125000 miles. The 1997 Ford Contour has 1 problems reported for engine pulleys have no timing marks. Installation Temporarily install crankshaft pulley.
Ensure crankshaft pulley timing marks are aligned. Qualsiasi aiuto o diagramma è molto apprezzato. You should check the belt at 60000 miles to see if it is getting worn.
I am trying to find where the timing marks are supposed to be on a 98 ford contour automatic trans. Browse Categories Answer Questions. Timing marks on both the camshaft and crankshaft pulleys must be aligned like this before removing or installing the timing belt-20L SOHC engines.
Tighten the tensioner bolt to hold it in place and remove the timing belt. Typical trade practice suggests that as a precaution the timing belt should be replaced every 60000 miles as in all other similar engines as timing belts tend to stretch. I recently started replacing a timing belt on a 95 countour and there are no timing marks other than the normal hash marks on the crank pulley with no timing pointer as Im finding out.
1996 Ford Contour. Timing marks on a 1997 ford escort 20 single overhead cam – Ford 1996 Contour question. I am not the original timing belt replacer so it came with faint marks at 12 and 1 oclock.
Posted on Sep 02 2010. Install tensioner and retaining bolt if necessary. The OEM Ford has not recommended a timing-belt replacement interval for the 1995 through 1997 Ford Contour 20 engine.
Inspect the timing mark on.
Source : pinterest.com